Axil GS Extreme 3.0

MAINTENANCE

Keep the headset away from high temperature areas, humidity, and dust.

EARTIP CLEANING, REUSABILITY and REPLACEMENT

ATTENTION! PRIOR TO CLEANING, REMOVE THE EARTIPS FROM THE EARPIECES TO PREVENT EQUIPMENT DAMAGE.

ATTENTION! WASH EARTIPS GENTLY WITH MILD SOAP IN LUKE WARM WATER. RINSE AND DRY EARTIPS THOROUGHLY BEFORE REUSE.

ATTENTION! REUSABLE EARTIPS MUST BE CHECKED PERIODICALLY BEFORE EVERY USE.

Silicone Eartips have up to a 5-year shelf life. For periodic use, replace eartips every 3–5 months depending on condition. For heavy industry use, replace every 14 days or if the tips are damaged.

Foam Eartips have up to a 5-year shelf life. For periodic use, replace eartips every 3–5 months depending on condition. For heavy industry use, replace every 14 days or if the tips are damaged or lose compressibility.

DISINFECTING

The GS EXTREME 3.0 product’s external surfaces, except for the eartips, can be disinfected by lightly rubbing the product for 60 seconds per surface with a cloth soaked (squeezing out excess liquids) with at least 60% ethanol or 70% isopropyl alcohol. Commercial 70% alcohol swabs, prep pads, or wipes can also be used. Allow to completely dry before using. If the earbuds become wet during disinfection, remove eartips and allow to dry before reassembly. Do NOT immerse the GS EXTREME 3.0 product in disinfecting liquid or use heat, ultraviolet light, sodium hypochlorite solution (commonly referred to as bleach) or hand sanitizers to disinfect, as this may damage the product. GS EXTREME 3.0 product may be adversely affected by certain chemical substances. Refer to the manufacturer for further information.

OBSOLESCENCE

The GS EXTREME 3.0 will remain in good condition with regard to shelf life while the product is stored in a warehouse under controlled conditions. For headset: Humidity is less than 80%, and the temperature is 0°C to 50°C. The headset manufacturing date (MM/YYYY) is printed on the packaging. The product lifetime of the headset (electronic parts) is 2 years from the given date of manufacture. The product lifetime of ear tips is up to 5 years from the given date of manufacture.

Step 1: Choose the Correct Concha Lock

The GS Extreme 3.0 comes with the medium concha lock pre-installed. If needed, swap to the size that gives the most secure and comfortable fit. Ensure the concha lock is positioned correctly on the earbud.

Step 2: Choose the Correct Ear Tip

Select the ear tip based on the level of hearing protection you need.

Foam tips provide maximum hearing protection and are recommended for shooting and loud environments.

Silicone tips provide mild hearing protection and are suitable for general audio use only.

Step 3: Install the Ear Tip

Push the selected ear tip onto the sound port as far as it will go to ensure a proper seal.

Step 4: Check Left and Right, Place Lanyard

Confirm left and right indicators, then place the lanyard behind your neck. Adjust the cinch to set the correct lanyard length.

Step 5: Compress the Foam Tip

If using foam tips, roll and compress them before insertion. This allows deeper insertion for best fit and protection.

Step 6: Insert Earbuds

Insert the earbud and tip into your ear canal as shown. Push in as deep as comfortable to achieve a full seal.

Step 7: Secure the Concha Lock and Ear Hook

Adjust the concha lock to sit comfortably in your ear and wrap the ear hook securely behind your ear.

Step 8: Power On

Press and hold the Bluetooth button on the control module to turn the GS Extreme 3.0 on. Press and hold again to power off.

Step 9: Activate Hearing Protection and Test

With the device powered on, touch and hold either touchpad for 3 seconds to activate hearing enhancement and protection. You will hear a confirmation sound.

Before exposure to loud noise, perform a quick test by clapping near your ears to ensure loud sounds are being suppressed. Always test before shooting.

Full official AXIL guide:
https://goaxil.com/pages/gs-extreme-3-0-how-to